Kitchen Fitting jobs in East Grinstead, West Sussex

Job Description

These are MFI and B@Q carcasses with gloss white slab ends, doors and drawers.
1x600 wall,2 x400 wall,1x600 drawerline and door and 1x800 drawerline and door.
The worktop will be a straight run of about 1.4m.This will need the end strips glued in

We will put together four of the six units.You will need to add on the gloss end panels to two of the wall units and two of the base units

The three wall units are MFI ones so a small adjustment to the door hinge will be required as the doors are B@Q ones.The base units will not need to be adjusted
as the are from B@Q

One cornice of 2400mm,one pelmet of 2400mm and one plinth of 3050mm will also need to be fitted and three drawers to the base units.Pilot holes may not be available for the drawers on the units so you may need to measure up here.

Two small cornices will need to be shaped on previous work now that the tiling is finished.There will be no tiling on this side of the kitchen.You fix to straight wall wallpaper surface

I will also need a bedroom wardrobe door hinge adjusted after a wallpaper job

Inspection only from 25/2 onwards by arrangement only
I have all the units.I expect to buy the doors and worktop in the Easter sales
so work could start from April

All mitre cuts are to be done with a machine please

* Added 15th February, 2013 :
Main bedroom will also need 3m of skirting mitred in

Job Description

Hello,

Need to fit kitchen and take the old one apart + floor and walls tiling.

Job Description

Old integrated larder fridge to be removed and new fridge installed. Advice needed for obtaining new fridge.

Job Description

Box in pipes at corner of kitchen, fit a new sink and work tops (laminate work tops about 5m in total length). Tile the kitchen walls - approximately 5 square metres.

Job Description

dismantle wall cupboard, fridge and freezer cupboards and remove granite worktop. Relocated microwave and pull out larder cupboard and provide plumbing for fridge.

Job Description

Fit and repair, as the existing dishwasher is supporting the worktop. The worktop (wood) is not properly fitted and it will require attention.

Job Description

"unfitted" kitchen units (3) with new worktop (4.5m long)... already cut to size with holes for tap plumbing & sink. All services in place. Worktop and sink need fitting and white sealing in. Other extra jobs such as tiling and basic carpentry.

* Added 9th July, 2012 :
Follow this link for illustration of kitchen cabinet units to be fitted. Everything is on site and ready for fitting now. Cash or invoice payment.

http://www.unfitted.co.uk/browse/SINK-BASE-CABINETS-FULL-HEIGHT-WITH-DRAWER-DOUBLE-4S-RECESSED/SCM-258

Job Description

I am interested in quotes to fit some of a kitchen. I need the following work to be done:

- Units to be fitted: 5 base units (inc oven unit) + 7 wall units (2 on ground)
- Appliances to be fitted: built-under oven, hob, hob extractor, dishwasher, sink, taps.
- cutting and fitting the worktop, including the sink and hob
- Tiling 7m wide by 1m high
- power to be run to dishwasher (spur of 2m) and extractor (spur of 2m)

All plumbing and gas lines are already fitted. All base units are already assembled.

All main items (units, worktops, appliances, plinths etc) will be provided by me. All tools, adhesives etc are to be provided by the builder.

The units are the standard Wickes Tenby range, and the work surfaces are veneered chipboard.

* Added 26th May, 2012 :
I have added photos to the listing below. The long wall with the oven in the middle is 3m from end to end. The two short runs are 2m each (including the fridge/freezer on the right). The tiling, which is probably under a metre, will go the whole length of the worktop and will finish half-way up the window.

* Added 27th May, 2012 :
Please note that the work can now be done any time (asap), so if you are free between 9th and 25th June, someone will be here then too.

Job Description

Kitchen fitted. Roof window installed. Flat roof overhauled. Small amount plastering. Ulity room units to be installed. Tiling on floor in kitchen and utility room.

Job Description

Had a kitchen installed but the worktops were not sealed around the edges where they meet the tiled walls and the sink sealant has come off. Please quote to seal worktops and sink. Approx 8 metres of worktop to be sealed.

Job Description

remove old sink and tap, minor adjustments needed to laminate worktop for size, fit and plumb new sing and tap.

old sink size 950 x 500 stainless steel
new sink size 1000 x 500 composite

quote needed for complete job

old sink and taps will be disposed of by myself

Job Description

Supply and fit kitchen doors, however I am happy to select doors from a supplier such as Howdens, however the fitter would require a trade card to purchase the doors on my behalf.

I also need some skirting boards fitted in the kitchen, incl finishing any necessary trim around the kitchen cupboards.

Finally I have x3 hall doors to be hung.

Job Description

We have bought a homebase kitchen, and would like it fitted. The kitchen is approximately 2.5m by 3.5m. We have removed all of the previous kitchen units except the sink unit and have fitted one wall of the new base units. There are 5 base units to fit (including sink, integrated cooker and washing machine) and 7 wall units. We would also like you to cut and fit the work surfaces, and plumb in the sink/washing machine. If possible I would like this done either this week or next.

* Added 13th November, 2011 :
Also, we have built all of the carcasses except for 2 wall units, so would only need drawers/shelves and doors fitted.

Job Description

I need a solid oak work top fitted in my kitchen with tap and sink trap and two cupboards, a corner cupboard and a single cupboard with draw,

Job Description

Hi, Have a kitchen (1.76m x 3.31m) that we need refitted and rewired.
It would be fitting units aready bought:
5 x wall cupboards
4 base units
1 x worktop
-Circuit Mains for kitchen domestic plugs requiring isolating.
-Kitchen sink needs moving approx 30cm along worktop.
Ideally work done within the next 6 weeks.
Need electric (to sign off an electricity compliance cert) and poss plumber