Electrical jobs in West Kensington, West London

Job Description

I have a small job, I'd like to add two double sockets to a wall and move an existing single socket up to match height of others and change it to a double.

Pictures attached.

Job Description

I have a very small kitchen on a bottom floor 5 storey council flat.

Kitchen is 220cm x 240cm

i was looking for quotes for rewriring of the kitchen which has 3 double plug sockets, up to current standard.

The kitchen has been completely gutted and is empty. i.e no units, applinces or sink. just walls and flooring.

Please can you give me a quote.

Job Description

Need an extractor fan fitted in the bathroom (have already selected a model just need somebody to check it's compatible) and to earth the boiler

Job Description

I need someone to install an extractor fan in my bathroom. I have all the parts already and the wiring is in the right place, no chasing in the wall required. I just need a qualified electrician to drill the hole through the wall and connect the external grill, piping through the wall and wire up the fan on the inside. Should be fairly straight orward.

Job Description

1) investigate and repair faulty doorbell

2) investigate and repair faulty ceiling lighting main bedroom

Job Description

Electrical safety Installation check required by qualified electrician and issue NICEIC certificate. This HMO licensed property consists of 10 bedsits and flats and each bedsit/flat has roughly 4 circuits.
This is a routine standard testing requirement and competitive rate will be welcomed for a continuous business.

Job Description

I am currently levelling and reflooring a bedroom and thought while the floors were up i'd see if i can get additional sockets installed.

This should be a quick job but would need to be done this week preferably.

This is likely to lead to further work as I am planning on installing a kitchen, bathroom, floors in other rooms, an outdoor tap, moving radiators (or possibly installing underfloor heating) and possibly installing a skylight over the next few months.

Job Description

I would like one double wall socket fitted inside a closet. There are electrical spurs already in the closet feeding an alarm and phone panel and there is a double wall socket on the opposite side of the wall where I would like the socket installed.

* Added 21st May, 2013 :
If you have plumbing skills too, I also need a pump replaced under my bath but this is not urgent so please do quote for the above electrical work if you do electrical work only.

Job Description

A newly built small office space with a kitchen area and seperate open space with about 4 power points downstairs and an open space with about 4 power points upstairs.

Ideally the space downstairs needs to house 7 desks, and so requires additional power outlets for computers.

The space upstairs ideally needs to run on a separate circuit, not a separate meter, just a circuit, so if a fuse trips it wont cut off the electricity for downstairs.

Job Description

I need someone to help convert wall lights in the living room and 2 bedrooms into "downlights" (spotlights).

The floorplan of the flat can be found here (http://www.dundeewharf.com/plans/index.shtml?typeb.inc)

Job Description

Fit 2 LED light bulbs sockets in the bathroom (for GU10 light bulbs)
(See picture attached, we'd like to have this replaced with a standard GU10 socket)

Job Description

My bathroom light will not turn on. It would appear it is simply a loose connection or the switch is broken.
A quote for time would be appreciated.

Job Description

Hi,

We are looking for someone who can connect our new cooker. The cooker is a Leisure GRB6CVK-BK 60cm freestanding cooker and requires a HO5W-FG5 x 1, 5mm2 / 3 x 4mm2 cable which was not supplied. We also require a ceiling light fitted which does not attach to the original light fitting. We are happy to call to discuss.

Availability before 10.30am or after 6pm preferred.

Thanks, Kerry

Job Description

I currently have one of the 2D 4pin lamp fittings type B in my bathroom where when the light switch cord is set to the on position it make the lamp turn on and the extraction fan at the same time.

I have changed bulbs before without any problems once they have had their lives worth but This time I have changed the bulb and the light still does not turn on fully. I thought maybe it was a faulty bulb so purchased another and still it has made no change. The light only partly comes on at the start of the two tubes of the 2D lamp but does not come on fully as it should. The extraction fan still comes on as it should.

The job I would like to request is take the exact same light fitting from the balcony and replace the bathroom fitting with this, or to repair the current fitting if it is possible.

Job Description

Supply and install new electrical distribution board with RCD protection. Issue electrical installation certificate.

Install 2 gang mk dimmer or a trailing edge dimmer

EICR report

PAT and gas safety certificates