Electrical jobs in Harrogate, North Yorkshire

Job Description

I am in the process of purchasing a house located in Follifoot Harrogate and would like an inspection doing of the electrics in the property before proceeding. It is a 4 bedroom detacted house built in the 1970's.

I am also looking for a gas survey incase a tradesman is registered with Corgi and can do this at the same time.

Job Description

Replace 1no storage heater with an electric radiator (same location in hallway) and replace a hairdryer with a shaving socket (in bathroom). The shaving socket will be about 20cm away from where the wires end for the hairdryer.

Job Description

I need a light re-connecting over the stairs (a previous one has been taken out so the hatch into the loft could be moved) and I'd like the light fitting in a bedroom replaced

Job Description

Home owner of 1970s house. All circuits checked by qualified Electrician in June.

The jobs - ceiling lights/lamps to be fitted to the ceiling in the hall, landing, utility room and a d/w room.

Plus extra double socket to be added in d/w room. Fan/light switch to be simplified and made into two seperate switches in same room. Plus new double wall mounted socket required. (wires to go inside wall. Therefore, a little plastering required).

Plus bathroom - new shave socket to be added and a new wall mounted extractor fan to be added with seperate switch/cord pull from the existing light switch.

Quote to include labour and an extractor fan & shaving socket please.

Many thanks.

Job Description

I want a full re-wire of domestic house lighting (which it should be noted is currently within steel conduit throughout).

Job Description

The original 1970 fusebox (fuse wire cartridge type) needs to be replaced with a 100A 8way consumer unit with 8 RCBO’s. Associated upgrade to earth wiring around the consumer unit to meet current standards. Safety certificate required.

House is a standard 1970 semi with currently 6 circuits/rings on the existing fusebox. Access to system is good (under stairs cupboard).

It is understood that provision cannot be made for faults encountered when making the upgrade. However, a statement of how the total outlay can be capped should be made to prevent an unknow/infinate final bill (e.g. if expensive problems are encountered, example costs are x and if budget does not allow then the result will be y).

There is no hurry for this work. However, it is mandatory that a fixed date be agreed to allow for holiday to booked. The date can be any time in the future but must be kept to.

Job Description

1 Wiring up underfloor heating (the elements have been laid, fused spurs are in place and the floor is in position, just the wiring to do). There are two of these to do straight away, and there will be another two in about 2 months time.
2 Wiring in a cooker hood in a new kitchen - Spur, wires and hood in place just needs wiring.
3 Fitting 3 under cabinet lights in a new kitchen. Spur is already in place - need lights fitting and wiring up.
4 Removing (and making safe) oven, sockets and hob from a kitchen that is to become a bathroom. Fitting external light switch to this room and lighting spur for illuminated mirror/vanity unit.
5 Create additional sockets (spurs) in two bedrooms.

Job Description

To cap off three unwanted wall lights, fit two new ceiling light fittings and replace 6 light switches.

Job Description

move the consumer box from the the sub cellar to the cellar head.

Job Description

Hi there,

We recently put in some new floorboards and when doing so damaged wires leading to a socket. Initially the socket worked but subsequently the socket has stopped working. Other sockets working in room so presume it is just the wire leading to that scoket that needs repairing/replacing.
Currently wire is wrapped with electrical insulating tap.
Timescale: Would like job done as soon as possible.

Thanks

Job Description

Attic room about to be plastered.
Need to instal 3 new double sockets (currently only one single socket)
Single socket only has one wire to it currently (i.e. already a spur)

* Added 22nd October, 2010 :
Forgot to mention - flooring is also being pulled up so no issue getting access to floorboards

Job Description

Please speak to Tom. A few electric points to move in the kitchen. Thank you.

Job Description

We have the following jobs that need doing. Unfortunately the only time frame available is 13th-16th July for these to be completed as we have builders in this week and plasterers in the following week.

The house is a fairly standard 1930s semi and we have just knocked the kitchen and dining room through to create one large room.

WORK TO BE CARRIED OUT:

Replacement Consumer Unit with 30mA RCD protection.

New circuits from Consumer Unit -
1 x UNPROTECTED switched double socket for fridge/freezer
1 x Cooker outlet

New outlets to be added to existing ground floor ring.
2 x 13A swiched double pole FCUs with neon cabled down to boxes/sockets under base units for Dishwasher and Washing Machine
1 x outlet for cooker hood
1 x switched double socket near cooker under base unit ( for use with future gas stove/fan)
1 x switched double socket above wall units (cooker wall) for future lighting etc.
1 x switched double socket above wall units (window wall) for future lighting etc.
3 x switched double sockets above work units

Please note we have removed the old kitchen units so it is an empty room to work in except one base unit under the sink. No plastering is required as the whole room is being skimmed. There is under floor access in part of the room (old dining room) but concrete floor where the old kitchen was.

Many Thanks

Job Description

We need a full rewire of our basement, in the next 3 months, whilst retaining power to the existing (old) circuits in the rest of the house (to be replaced later).

All furniture & ktichen units will be removed in advance by me.

Any vertical cable runs are to be chased into the (brick) walls (i.e. no surface mounted conduit wherever possible).

Good quality fixtures (switches/ MCBs/ downlights/ pendants/ alarms etc.) to be supplied (please specify the make you will supply) as per the following:

Utility
1 x light on 1 way switch
2 x 13A Double switched socket outlets
1 x multi way MCB board with 2 RCDs
1 x gas earth bond
1 x water earth bond

Sitting room
1 x 3 wall light points on 1 way switch
1 x 1 light on 1 way switch
1 x 1 wall light point on 1 way switch
4 x 13A double switched socket outlets
1 x mains linked smoke alarm (with "link" capability for others in future)

Kitchen
1 x 3LV downlights - fire rated on 2 way switch pr
1 x 5LV downlights - fire rated on 2 way switch pr
1 x 2 light points on 1 switch fuse (units)
1 x 2 light points on 1 switch fuse (units)
1 x 2 external bulkheads on 1 way switch
1 x 13A switch fuse with remote point (hood)
6 x 13A double switched socket outlets
1 x cooker circuit with isolator & flex outlet
1 x immersion circuit & switch - no element
1 x S plan heating system (no controls)

Hall/Stairs
1 x 5LV downloghts fire rated on 2 way switch pr
1 x ceiling pendant connected to other lights
1 x 13A double switch socket outlet
1 x mains linked carbon monoxide alarm (with "link" capability for others in future)
1 x room stat wiring (no stat)

Store
1 x 1 light on 1 way switch
1 x 13A double switched socket outlet

WC
1 x 2 lights on 1 way switch

Log store
1 x 1 light on 1 way switch

Coal store
1 x 1 light on 1 way switch

Workshop
1 x 1 single 1500mm flourescent on 1 way switch
3 x 13A double switch socket outlets

1st Floor
Dining room
3 x 13A double switched socket outlets

Lounge
4 x 13A double switched socket outlets

Hall
1 x 13A double switched socket outlets

Detached garage (approx 5m from workshop)
1 x 20m 13A SWA cable in trench (I will dig this)
1 x Light on 1 switch fuse
1 x 13A double switched socket outlet

Sketched plan with measurements available on request.

* Added 29th March, 2010 :
I've attached a rough sketch plan - if this is not sufficiently legible please let me know and I will produce a version on computer. Please note that the ground floor is not shown in the sketch but hopefully is relatively straightforwards as it is only the ground floor sockets we require for the quote (and the ground floor dining room/lounge/hall are the same size as the basement kitchen/sitting room/hall respectively).

I should have added on the specification, that the consumer unit will need, in addition to the circuits for the work specified, sufficient space for at least 6 additional circuits not in the spec/plan. These are for the future upstairs circuits. If this presents difficulties please let me know as we could just add another CU in future if that is easier/ cheaper.

Job Description

Sub-contractor needed: Hard-wired smoke alarms for HMO property Knaresborough Road area of Harrogate, downstairs has kitchen, dining, bedroom, hallway, upstairs has a landing, bathoom and two bedrooms. Accessible loft above.

Work to be carried out end of May/beginning of June as part of bringing property up to regulations. No making good required, plasterers will be on site.

Replies with fixed quotation please and earliest start date. Access for survey is available if required. Payment will be cheque on completion and receipt of invoice. Part P qualified only please.

* Added 21st May, 2010 :
Sorry gents, believe I've caused a bit of confusion about the loft, what I was trying to say is that there is access to the loft to cable to the first floor detector, not that there's a loft room that requires another detector.